TIGm 1.1 - Submersible electric pump with single-phase grinder 1.5 HP
Flow rate up to 150 l/min (9 m³/h). Head up to 24 m. 1.1 Kw (1.5 HP) motor.
The Pedrollo TIGm 1.1 single-phase grinder pump is equipped with a high-resistance tempered stainless steel grinder.
The pump is equipped with a 10 meter cable, it can be immersed up to 5 meters underwater.
The TIGm 1.1 allows for the complete shredding of solid bodies and fibres contained in waste water and waste water in the domestic and civil sectors, for conveyance under pressure into the sewer system through small diameter pipes.
It has a flow rate that varies from 20 to 150 litres per minute with a head of 2 to 24 metres.
It must be powered by a single-phase voltage, has a horsepower of 1.5 HP and the temperature of the liquid to be pumped ranges from -15 degrees centigrade up to +40.
It has an IP68 certification which is safe from dust and water ingress.
The TIGm 1.1 is equipped with an external electrical panel for greater operational safety thanks to the special capacitor that significantly increases the torque. The panel includes a manually reset motor protection switch.
The pump is made of materials such as cast iron and stainless steel which give the pump good resistance and allow it to last over time.
- Motor connection
- SINGLE PHASE
- Power (Kw)
- 1.1
- Power (HP)
- 1.5
- Absorption at 230V (A)
- Delivery port
- 1 "1/2
- Body Pump
- Cast iron
- Impeller
- Technopolymer
- Number of impellers
- 1
- Motor shaft
- AISI 431 stainless steel
- Check valve
- no
- Degree of protection
- IP 68
- Flow rate min. (l./min.)
- Max flow (l./min.)
- Min head (m.)
- Max head (m.)
- Cable length (m)
- Employments
- slightly dirty waters, drainage, drying up
- Liquid temperature max. (° C)
- Height (cm)
- Width (cm)
- Depth (cm)
- Weight kg)
- Guarantee
- 2
Construction
Bearings
| Pump side motor bearing | 6303 2RS-C3 |
| Opposite side engine bearing | 6203 ZZ-C3E |
Tree seal
| Type of seal | Double Mechanical Seal in oil chamber |
| LM diameter | 14 |
| LM fixed ring | Silicon Carbide |
| LM rotating ring | Graphite |
| LM Elastomer | NBR |
| Narrowing DN1=450 DN2=350 | MG1-14D SIC |
| LP diameter | 14 |
| LP fixed ring | Silicon Carbide |
| LP Rotating Ring | Silicon Carbide |
| LP Elastomer | NBR |
Materials
| 1.0 - Pump Body | Cast iron GJL 200 EN 1561 |
| 3.0 - Impeller | Technopolymer |
| 3.2 - Shredder | Stainless steel EN 1.4125 (AISI 440C) hardened |
| 4.0 - Pump Tree | Stainless steel EN 1.4057 (AISI 431) |
| 6.0 - Engine carrier | Stainless steel EN 1.4301 (AISI 304) |
| 7.0 - Lantern | Cast iron GJL 200 EN 1561 |
Compare with Similar Products
 TIGm 1.1 - Submersible electric pump with single-phase grinder 1.5 HPThis product Flow rate up to 150 l/min (9 m³/h). Head up to 24 m. 1.1 Kw (1.5 HP) motor. |  TIGm 0.55 - Submersible electric pump with single-phase grinder 0.75 HPFlow rate up to 130 l/min (7.2 m³/h). Head up to 16 m. 0.55 Kw (0.75 HP) motor. |  TIGm 0.75 - Submersible electric pump with single-phase grinder 1 HPFlow rate up to 140 l/min (7.8 m³/h). Head up to 18.5 m. 0.75 Kw (1 HP) motor. |  TIGm 1.5 - Submersible electric pump with 2 HP single-phase grinderFlow rate up to 250 l/min (9 m³/h). Head up to 21 m. 1.5 Kw (2 HP) motor. | |
|---|---|---|---|---|
| Motor connection | Motor connection SINGLE PHASE | Motor connection SINGLE PHASE | Motor connection SINGLE PHASE | Motor connection SINGLE PHASE |
| Power (Kw) | Power (Kw) 1.1 | Power (Kw) 0.55 | Power (Kw) 0.75 | Power (Kw) 1.5 |
| Power (HP) | Power (HP) 1.5 | Power (HP) 1 | Power (HP) 1 | Power (HP) 2 |
| Absorption at 230V (A) | Absorption at 230V (A) -- | Absorption at 230V (A) -- | Absorption at 230V (A) -- | Absorption at 230V (A) -- |
| Delivery port | Delivery port 1 "1/2 | Delivery port 1 "1/2 | Delivery port 1 "1/2 | Delivery port 1 "1/2 |
| Body Pump | Body Pump Cast iron | Body Pump Cast iron | Body Pump Cast iron | Body Pump Cast iron |
| Impeller | Impeller Technopolymer | Impeller Technopolymer | Impeller Technopolymer | Impeller Technopolymer |
| Number of impellers | Number of impellers 1 | Number of impellers 1 | Number of impellers 1 | Number of impellers 1 |
| Motor shaft | Motor shaft AISI 431 stainless steel | Motor shaft AISI 431 stainless steel | Motor shaft AISI 431 stainless steel | Motor shaft AISI 431 stainless steel |
| Check valve | Check valve no | Check valve no | Check valve no | Check valve no |
| Degree of protection | Degree of protection IP 68 | Degree of protection IP 68 | Degree of protection IP 68 | Degree of protection IP 68 |
| Flow rate min. (l./min.) | Flow rate min. (l./min.) -- | Flow rate min. (l./min.) -- | Flow rate min. (l./min.) -- | Flow rate min. (l./min.) -- |
| Max flow (l./min.) | Max flow (l./min.) -- | Max flow (l./min.) -- | Max flow (l./min.) -- | Max flow (l./min.) -- |
| Min head (m.) | Min head (m.) -- | Min head (m.) -- | Min head (m.) -- | Min head (m.) -- |
| Max head (m.) | Max head (m.) -- | Max head (m.) -- | Max head (m.) -- | Max head (m.) -- |
| Cable length (m) | Cable length (m) -- | Cable length (m) -- | Cable length (m) -- | Cable length (m) -- |
| Employments | Employments slightly dirty waters, drainage, drying up | Employments slightly dirty waters, drainage, drying up | Employments slightly dirty waters, drainage, drying up | Employments slightly dirty waters, drainage, drying up |
| Liquid temperature max. (° C) | Liquid temperature max. (° C) -- | Liquid temperature max. (° C) -- | Liquid temperature max. (° C) -- | Liquid temperature max. (° C) -- |
| Height (cm) | Height (cm) -- | Height (cm) -- | Height (cm) -- | Height (cm) -- |
| Width (cm) | Width (cm) -- | Width (cm) -- | Width (cm) -- | Width (cm) -- |
| Depth (cm) | Depth (cm) -- | Depth (cm) -- | Depth (cm) -- | Depth (cm) -- |
| Weight kg) | Weight kg) -- | Weight kg) -- | Weight kg) -- | Weight kg) -- |
| Guarantee | Guarantee 2 | Guarantee 2 | Guarantee 2 | Guarantee 2 |