UPm 4/4 (10m) - submersible Pump single phase
Flow rate up to 120 l/min (7.2 m3/h). Head up to 53 m. Motor 0.75 Kw (1 HP). 10 metres of cable.
The prevalent characteristic of the submersible pump UP is the inability to stop responding, even after long periods of inactivity, thanks to innovative and patented technical solutions.
The UP subverts the classic design of the submersible pumps 5”. In fact, compared to pumps of the same type is constructed in an inverse manner, i.e. with the engine in the lower part, the hydraulic cross-section at the top (hence the name UP).
Among his revolutionary strengths are a greater compactness and a system of floating impellers independent that allows you to pump clean water with a maximum sand content can reach 150 g/m3, the only in the world of 5”.
In addition, the UP has reduced consumption, a valve that eliminates the“effect” bell-to facilitate the expulsion of air bubbles which may form inside the pump and the inlet grating raised and not on the bottom to prevent the passage of sand, leaves and other foreign matter that may clog plumbing and reduce the performance.
The UPS is equipped with a system of flushing the forced oil lubrication of the mechanical seals and is available in the versions with float switch or without. Can work both in vertical and horizontal position.
For the high efficiency and reliability is recommended for pumping clean water in domestic, civil, agricultural, irrigation of orchards and gardens, for raising pressure, etc.,
- Motor connection
- SINGLE PHASE
- Motor power (HP)
- 1
- Absorption at 230V (A)
- 6.2
- Capacitor
- 20 µF450 VL
- Delivery port
- 1 "1/4
- Body Pump
- AISI 304 stainless steel
- Impeller
- Noryl
- Number of impellers
- 4
- Motor shaft
- AISI 431 stainless steel
- Check valve
- no
- Degree of protection
- IP 68
- Flow rate min. (l./min.)
- 20
- Max flow (l./min.)
- 120
- Min head (m.)
- 16
- Max head (m.)
- 53
- Cable length (m)
- 10
- Employments
- irrigation, water supply, pressurization systems
- Liquid temperature max. (° C)
- 15
- Height (cm)
- 48.2
- Outside diameter (cm)
- 15
- Weight kg)
- 15.8
- Guarantee
- 2
|
|
|
|
|
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Bearings
| Pump side motor bearing | 6303 2RS - C3 |
| Opposite side engine bearing | 6203 ZZ - C3E |
Tree holding
| Type of seal | Double mechanical seal in oil chamber |
| Engine side model | STA-17 |
| LM diameter | 17 |
| LM fixed ring | Ceramic |
| LM rotating ring | Graphite |
| LM elastomer | NBR |
| Shrinkage DN1=450 DN2=350 | ST1-16 |
| LP diameter | 16 |
| LP fixed ring | Silicon carbide |
| LP rotating ring | Graphite |
| LP elastomer | NBR |
Materials
| 2.1 - Seal holder cover | Stainless steel EN 1.4301 (AISI 304) |
| 3.0 - Impeller | Reinforced technopolymer |
| 4.0 - Pump shaft | Stainless steel EN 1.4057 (AISI 431) |
| 5.1 - Diffuser | Reinforced technopolymer |
| 5.3 - Diaphragm/Diffuser Cover | Stainless steel EN 1.4301 (AISI 304) |
| 6.2 - Engine sleeve | Stainless steel EN 1.4301 (AISI 304) |
| 7.2 - Pump shirt | Stainless steel EN 1.4301 (AISI 304) |
| 7.3 - Cable cover | Stainless steel EN 1.4301 (AISI 304) |
Compare with Similar Products
 UPm 4/4 (10m) - submersible Pump single phaseThis product Flow rate up to 120 l/min (7.2 m3/h). Head up to 53 m. Motor 0.75 Kw (1 HP). 10 metres of cable. |  UPm 4/3 (10m) - submersible Pump single phaseFlow rate up to 120 l/min (7.2 m3/h). Head up to 40 m. Motor 0.55 Kw (0.75 HP). 10 metres of cable. |  UPm 4/5 (10m) - submersible Pump single phaseFlow rate up to 120 l/min (7.2 m3/h). Prevalence of up to 67 m. Motor 1.1 Kw (1.5 HP). 10 metres of cable. |  UPm 4/6 (10m) - submersible Pump single phaseFlow rate up to 120 l/min (7.2 m3/h). Head up to 80 m. Motor 1.5 Kw (2 HP). 10 metres of cable. | |
|---|---|---|---|---|
| Motor connection | Motor connection SINGLE PHASE | Motor connection SINGLE PHASE | Motor connection SINGLE PHASE | Motor connection SINGLE PHASE |
| Motor power (HP) | Motor power (HP) 1 | Motor power (HP) 0.75 | Motor power (HP) 1.5 | Motor power (HP) 2 |
| Absorption at 230V (A) | Absorption at 230V (A) 6.2 | Absorption at 230V (A) 5.0 | Absorption at 230V (A) 7.2 | Absorption at 230V (A) 8.7 |
| Capacitor | Capacitor 20 µF450 VL | Capacitor 16 µF450 VL | Capacitor 25 µF450 VL | Capacitor 35 µF450 VL |
| Delivery port | Delivery port 1 "1/4 | Delivery port 1 "1/4 | Delivery port 1 "1/4 | Delivery port 1 "1/4 |
| Body Pump | Body Pump AISI 304 stainless steel | Body Pump AISI 304 stainless steel | Body Pump AISI 304 stainless steel | Body Pump AISI 304 stainless steel |
| Impeller | Impeller Noryl | Impeller Noryl | Impeller Noryl | Impeller Noryl |
| Number of impellers | Number of impellers 4 | Number of impellers 3 | Number of impellers 5 | Number of impellers 6 |
| Motor shaft | Motor shaft AISI 431 stainless steel | Motor shaft AISI 431 stainless steel | Motor shaft AISI 431 stainless steel | Motor shaft AISI 431 stainless steel |
| Check valve | Check valve no | Check valve no | Check valve no | Check valve no |
| Degree of protection | Degree of protection IP 68 | Degree of protection IP 68 | Degree of protection IP 68 | Degree of protection IP 68 |
| Flow rate min. (l./min.) | Flow rate min. (l./min.) 20 | Flow rate min. (l./min.) 10 | Flow rate min. (l./min.) 20 | Flow rate min. (l./min.) 20 |
| Max flow (l./min.) | Max flow (l./min.) 120 | Max flow (l./min.) 80 | Max flow (l./min.) 120 | Max flow (l./min.) 120 |
| Min head (m.) | Min head (m.) 16 | Min head (m.) 12 | Min head (m.) 20 | Min head (m.) 24 |
| Max head (m.) | Max head (m.) 53 | Max head (m.) 40 | Max head (m.) 67 | Max head (m.) 80 |
| Cable length (m) | Cable length (m) 10 | Cable length (m) 10 | Cable length (m) 10 | Cable length (m) 10 |
| Employments | Employments irrigation, water supply, pressurization systems | Employments water supply, pressurization systems, irrigation | Employments irrigation, water supply, pressurization systems | Employments irrigation, water supply, pressurization systems |
| Liquid temperature max. (° C) | Liquid temperature max. (° C) 15 | Liquid temperature max. (° C) 40 | Liquid temperature max. (° C) 40 | Liquid temperature max. (° C) 40 |
| Height (cm) | Height (cm) 48.2 | Height (cm) 42.5 | Height (cm) 50.9 | Height (cm) 55.6 |
| Outside diameter (cm) | Outside diameter (cm) 15 | Outside diameter (cm) 15 | Outside diameter (cm) 15 | Outside diameter (cm) 15 |
| Weight kg) | Weight kg) 15.8 | Weight kg) 14.2 | Weight kg) 17.2 | Weight kg) 19.5 |
| Guarantee | Guarantee 2 | Guarantee 2 | Guarantee 2 | Guarantee 2 |
